How to Install Drip Edge With Gutters (What the Code Requires)
There’s a particular kind of rot that shows up behind gutters: soft, dark fascia boards and peeling paint just under the roof edge, even though the gutters themselves look fine and don’t leak. The usual culprit is a few inches of metal that’s missing, too short or installed in the wrong order. Rainwater clings to the underside of the roof edge, curls back and runs down behind the gutter instead of into it.
Drip edge is an L- or T-shaped metal strip along the roof’s edges that throws water clear of the fascia and into the gutter. On shingle roofs, the International Residential Code requires it at both the eaves and the rakes, overlapped at least 2 inches, fastened at least every 12 inches, with the roof underlayment installed over the drip edge along the eaves and under it along the rakes (IRC R905.2.8.5). Where gutters are involved, a wider drip edge or a gutter apron should reach over the back of the gutter so no water can slip behind it.
What the code requires
For asphalt shingle roofs, Section R905.2.8.5 of the 2021 International Residential Code says (IRC):
- Drip edge at eaves and rake edges.
- Adjacent pieces overlapped at least 2 inches.
- It must extend at least ¼ inch below the roof sheathing and at least 2 inches back onto the roof deck.
- It must be fastened to the deck at no more than 12 inches on center.
- Underlayment goes over the drip edge at the eaves and under it at the rakes.
That last rule is the one that matters most for gutters: at the eave, any water that gets under the shingles runs down the underlayment and out over the drip edge into the gutter, rather than behind it. This Old House’s step-by-step follows the same order: drip edge under the felt at the eaves and over the felt at the rakes (This Old House).
Choosing the right profile
| Type | Shape | Notes |
|---|---|---|
| Type C (L-style) | Simple right angle | Common and inexpensive, about $0.30 to $1 per linear foot (This Old House) |
| Type D (T-style) | Angled flange that kicks out past the fascia | Reaches further over the gutter; recommended for most residential roofs by the Asphalt Roofing Manufacturers Association, per This Old House (This Old House) |
| Gutter apron | Like a wider L with a steeper angle | Laps over the back of the gutter; the fix when water runs behind gutters (This Old House; Family Handyman) |
In rainy or snowy climates, This Old House’s Tom Silva recommends a wider drip edge (This Old House).
How drip edge meets the gutter
The goal is simple: no gap between roof edge and gutter that water can fall through.
- Gutter apron flashing goes under the shingles and over the back edge of the gutter, nailed with 1-inch roofing nails about every two feet and lapped about two inches at joints (Family Handyman).
- Gutter height. Bob Vila’s install guide sets the gutter about 1¼ inches below the edge of the flashing (Bob Vila). This Old House adds a check: the front edge of the gutter shouldn’t stick up above the roof plane; lay a straightedge on the roof, and if it hits the gutter’s front edge, the gutter is too high (This Old House).
- Snow country. Silva recommends running a self-sealing membrane from the roof down onto the fascia before the drip edge goes on (This Old House).
Installation steps (new roof or re-roof)
- Start at the eaves, so water from the rakes flows over the eave drip edge at the corners (Family Handyman).
- Set the drip edge on the deck before the underlayment at the eaves.
- Fasten with roofing nails, no more than 12 inches apart by code; Silva prefers 8 to 10 inches (IRC; This Old House).
- Overlap joints at least 2 inches (IRC).
- Lay underlayment over the eave drip edge, then install rake drip edge over the underlayment.
- Let the shingles overhang the drip edge by about ⅜ to ½ inch, “a finger’s width”, so water drips clear (This Old House).
Retrofitting drip edge under existing shingles is possible but fiddly, and pressing too hard can damage the deck (Family Handyman). If you’re not comfortable working on the roof, hire a roofer (This Old House).
Common mistakes
From This Old House’s list, with Tom Silva (This Old House):
- Shingles flush with the drip edge instead of overhanging it, so water runs back along the underside.
- Drip edge tight against the fascia. Silva recommends a gap: the edge sitting about 1½ to 1¾ inches away from the fascia board. (Other This Old House pages give different figures, such as about ¾ inch past the fascia (This Old House), so follow the product’s instructions for your gutter setup.)
- Joints not overlapped, or overlapped too little.
- Fasteners too far apart, or the wrong nails.
- The wrong profile for your climate.
Compare installed prices near you
Free quotes from up to 3 local gutter guard installers. No obligation.
Sources
- International Code Council, 2021 International Residential Code, Section R905.2.8.5 Drip edge. codes.iccsafe.org
- This Old House, “Step by Step Guide to Installing a Drip Edge” (June 2026). thisoldhouse.com
- This Old House, “Common Drip Edge Installation Mistakes” (June 2026). thisoldhouse.com
- This Old House, “Roof Drip Edge Types” (May 2026). thisoldhouse.com
- This Old House, “How To Install Aluminum Gutters” (May 2026). thisoldhouse.com
- Family Handyman, “How to Install Gutters” (October 2024). familyhandyman.com
- Family Handyman, “How to Fix a Roof Drip Edge” (October 2024). familyhandyman.com
- Bob Vila, “How to Install Rain Gutters” (May 2025). bobvila.com